GTA

PCP - HPA - C02 Gate => Crosman Discovery Forum => : SDale September 12, 2009, 03:21:38 PM

: Thinking of getting a Disco. Need to know a few things first though.
: SDale September 12, 2009, 03:21:38 PM

I've been thinking of getting a disco since they came out. But never really researched them much.

BUT, what I wanted to know was.... Will a 22xx/13xx pistol grip/trigger group bolt up to the Disco main tube with no mods???

If it needs to be modified, what needs to be done to get it to fit?????

: RE: Thinking of getting a Disco. Need to know a few things first though.
: SDale September 13, 2009, 11:05:32 AM

Lotsa looks, and now replies.

I guess there's folks out there other than me that wanna know too! hehe

I'll find out sooner or later.

: RE: Thinking of getting a Disco. Need to know a few things first though.
: preez September 13, 2009, 11:48:28 AM

Hey Sam, I am no expert on 22xx/13xx series, but I think at least the 22xx trigger group should fit OK. I fixed someone's disco with a 22xx sear in it and it was a drop in fit and worked quite nicely! I don't know how the pistol grip mounts, but you could probably fit it with small modifications. There are bunch of Disco pistols out there.

Hope this helps

Chris

: RE: Thinking of getting a Disco. Need to know a few things first though.
: SDale September 13, 2009, 12:16:54 PM

Hmmm... Sounds promissing! Thanks Preez!

The 22xx/13xx trigger groups are the same and they mount with 2 screws.

Anyone got a picture of the bottom of a Disco lower reciever tube with a center to center measurment of the screw holes?

: RE: Thinking of getting a Disco. Need to know a few things first though.
: melloroadman September 13, 2009, 03:04:43 PM

Sam this has been done and talked about on the green allot you might take a look there .Marvin

: RE: Thinking of getting a Disco. Need to know a few things first though.
: SDale September 15, 2009, 03:53:32 PM

OK, took me a couple days of weeding, but the answer is YES. SO, now I need to gather funds for a Disco & Pump combo.

: SAM TAKE A LOOK
: melloroadman September 16, 2009, 03:17:40 PM

At the MA 2260  hunter. Marvin
http://www.mountainaircustomairguns.com/our_guns.htm

: RE: SAM TAKE A LOOK
: SDale September 16, 2009, 03:33:25 PM

Thanks for the link Marvin!

I saw that a while back during a browsing/research session. But I've got something a little different in mind. It involves a riser breech and a Green Mountain .38 cal Barrel blank

: LOOKING FORWARD TO YOUR PROGESS REPORTS N/T
: melloroadman September 16, 2009, 04:55:31 PM

N/T

: RE: Thinking of getting a Disco. Need to know a few things first though.
: khadux September 17, 2009, 05:59:35 AM

I'm thinking about doing the same which is to modify one of my disco to using a pistol grip and trigger from the 22xx serries.  what parts do i need?

: RE: Thinking of getting a Disco. Need to know a few things first though.
: SDale September 17, 2009, 01:52:49 PM

From what I've read and understand, all you need to install a 13/22xx series grip frame on a disco it the grip frame and 2 screws. Noting else. Now if you wanna SHOOT it, then you'll probably need a stock! hehe

: PARTS NEEDED
: melloroadman September 18, 2009, 06:22:24 AM

I e-mailed Roy and besides the trigger group and stock there is little needed . If you look at the picture of his ma 2260 you will see a for arm . He said he uses the 2250 arm and he makes a plug to replace the gauge that has to be removed to use it . If you use a 1377 as a donor as I will be there is a small bracket that you will have to make or buy  . Look at the part list on the crosman sight and you can see the parts I am talking about . Marvin