« previous next »
Pages: [1]   Go Down

Author Topic: Im Still At It,,,, ")  (Read 2532 times)

Offline Timmyj1959@yahoo.com

  • Hero Member
  • *****
  • Posts: 3716
    • http://dragonslayer
Im Still At It,,,, ")
« on: December 03, 2009, 12:05:22 PM »
I am more intense than ever trying to get my new stock buisness off the ground folks. I spend EVERY spare moment I have in the shop. While I look every day at Marauder 001 up on the shelf only needing a little final shaping,,, I am focused right now on developing Discovery stocks & learning how to operate my new duplicator machine. Im getting a better feel for the machine now. Yesterday I duplicated my first Disco stock inletting,,,, DISMAL FAILURE!!To say I was heart broken would be a huge understatement. Nice fit for sure,,, but it pointed off "Left Field" like you would not believe!! Long story short,, I figured out the problem & Im back on my game!!Stay tuned Folks,,,, Im gonna have some exiting new products soon!! WORD!!Timbo.
Logged

Offline Timmyj1959@yahoo.com

  • Hero Member
  • *****
  • Posts: 3716
    • http://dragonslayer
RE: Im Still At It,,,, ")
« Reply #1 on: December 03, 2009, 12:07:13 PM »
Logged

Offline Big_Bill

  • Hero Member
  • *****
  • Posts: 5615
    • http://
RE: Im Still At It,,,, ")
« Reply #2 on: December 03, 2009, 04:10:44 PM »


You'll learn somethin new every day Timmy !!!!!!



But it looks like whatever you did learn, sure is lookin fine !!!!!!!



Keep up the beautiful work there nephew :-)



You a just doin fine :)



Uncle Bill

Logged
Life Member of The United States of America
Life Member of the National Rifle Association
Member Air Guns Addicted Anonymous
SHOOT SAFE ! - SHOOT WELL ! - SHOOT OFTEN !
Always Use A Spring Compressor ! and Buy the GREAT GRT-III & CBR Triggers, cause they are GRRRREAT !

Offline shadow

  • Hero Member
  • *****
  • Posts: 11453
    • http://airguncamo@yahoo.com
RE: Im Still At It,,,, ")
« Reply #3 on: December 03, 2009, 09:38:41 PM »
Keep after it bro you'll be pumping those stock's out in no time at all.:) Ed
Logged
I airgun hunt therefore I am... };)  {SHADOWS Tunes & Camo}  airguncamo@yahoo.com

Offline Gene_SC

  • Hero Member
  • *****
  • Posts: 11378
    • http://www.airguntoys.com
Re: Im Still At It,,,, ")
« Reply #4 on: December 04, 2009, 12:21:48 AM »
Looks pretty amazing to me..:)
Logged
THE ONES I SLEEP WITH: BSA Lightning XL, AA TX-200, AA ProSport, BSA Ultra, HW-97K, Crosman NPSS .177, FX Cyclone, HW-30 Nicle Plated, AA-S200, Crosman Marauder, CZ-634, R-9 DG, Webley/Scott UK Tomahawk, Benji Kantana, Benji Marauder, Benji Discovery.....
....

Gene\'s Tunz n Toyz
Springer Tunin

Offline geewhiz380

  • Hero Member
  • *****
  • Posts: 1878
    • http://
Re: Im Still At It,,,, ")
« Reply #5 on: December 04, 2009, 01:14:15 AM »
timmy u will have your truck back in no time ...jorge
Logged

Offline Rontier

  • Sr. Member
  • ****
  • Posts: 385
    • http://
Re: Im Still At It,,,, ")
« Reply #6 on: December 04, 2009, 04:50:34 AM »
Wow Timmy that is a very nice set up!
I've not seen one like that.
& your very good too,
:)
Logged

Offline jake

  • Hero Member
  • *****
  • Posts: 1255
    • http://
Re: Im Still At It,,,, ")
« Reply #7 on: December 05, 2009, 03:21:12 AM »
its looking goood!
Logged
if at first you dont succeed, re-load, kill count 2010.
(6)squirrel
()opposum
()skunk
()chipmunks
()squirrel
()raccoon
(1)starling
()grackle
()sparrows

Offline Als69GT

  • Sr. Member
  • ****
  • Posts: 280
    • http://www.saveonemorechild.com
Re: Im Still At It,,,, ")
« Reply #8 on: December 08, 2009, 04:06:47 AM »
Square and plumb - words I heard my grandfather and dad say so often. They were both carpenters, I am a welder and steel fabricator and I live by these words as well

Al

P.S. When I forget that, the cussin is not far behind
Logged
I know there is a fine line between a hobby and an obcession, to bad I sped over it at about a hundred !!

Offline dademoss

  • GTA Donations
  • ******
  • Posts: 40
    • http://
Re: Im Still At It,,,, ")
« Reply #9 on: December 08, 2009, 08:39:35 AM »
My grandfather and dad always said "straight and true" and "it's all in the setup", they were both machinists :-)

Once you have your machine set up right, you will be making some fabulous furniture!
Logged
Dave
Pages: [1]   Go Up
« previous next »