Author Topic: Guy wants me to pop a couple nuisance beavers  (Read 7505 times)

Offline only1harry

  • Hero Member
  • *****
  • Posts: 3155
    • http://
No powder burner needed...!!
« Reply #15 on: May 11, 2010, 12:11:12 PM »
I don't know a lot about the Marauder .25 and how much energy it puts out, but if it's more than the .22 version, or over 30fpe at the muzzle, then it should do the job just fine, but only with a well placed shot in the head and not from very far away.  

I would try and get within 30yds with the Marauder.  The goal is to quickly and humanely kill it on the spot, and post the pics here afterwards.. like immediately :)  But seriously speaking, this means getting close to ensure an accurate shot to the head but where it counts on the head, not its jaw, nose, or somewhere on the neck.  It has to be its brain.  

If you can get your hands on a powerful PCP like a Condor (.22 or .25), even better.  You could take the beaver from 40-50yds easily but again, it has to be a very good head shot so it goes down fast and you don't just injure it and lose it.  We had a kid here about 2-3yrs back (or was it on the Dianawerk forum?) that took a 35lb beaver with his 350 .177.  A single shot to the head from 20 or 30yds I believe, and he said it dropped dead in its tracks.  

Beavers actually get pretty large but many Coyotes (and plenty of fox) have been taken with mid powered PCP's and Magnum Springers.  A beaver's head is probably slightly  harder or thicker than a Coyote's, but it is just bone, not steel or pressure-treated wood.  We are not talking about a bear or a wild boar here.  Even if the beaver's head is equivelant to say wood..  that's no problem.  My Condor almost goes through a pressure-treated 2x4" (or 2x8") from 25yds out.  You can see the splinters sticking out in the back or part of the pellet.  At 10yds Kodiaks go right through it as long as they go >1,040fps.  I think the challenge here with the Beaver would be to get up close within normal "airgun ranges" (25 to 35yds), especially because it is a large one with a good size head.  It would not be much of a challenge taking a shot at it with a 30-06 from 75 or 100yds out.  A .17HMR or .22 WMR maybe, not not a centerfire gun.  

If I had to use a powder burner, I would just use my .22LR (~125fpe) which is deadly accurate at 50yds.  

You are only going to need about 15fpe on impact (to the head) to drop this beaver so an airgun will do.  15fpe is the same to shooting the beaver with a Diana 34 .177 or .22 at point-blank range.  Do some of you think you cannot kill a beaver with a shot like that (900fps w/.177 pellet or 680-700fps in .22) betwen the eyes from 1" away?  I know people (through other forums) that have killed feral dogs bigger than a beaver with the same or less "firepower" from 15yds out.  It's all about shot placement.  Forget the powder burners.  You can take the beaver with your Marauder if you are patient enough and practice a lot until you can place that pellet inside a nickel-sized hole every time (at 30yds and beyond).  Should not be too hard to do with a PCP like the Marauder.  Good luck and let us know the outcome.
Springers:
Diana 36 .177
Diana 350 .22 (donated by Timmy!)
Diana 350 .177
PCP\'s:
Air Force Condor .22 (Airhog)
Air Force Condor .25 (Talon Tunes)
Air Force Condor .25 (Lemak)  
CO2/Pump:
RWS Hammerli 850 .22
Crosman 2240 Custom .22
A few Crosman pumpers .177

Offline crowpopper

  • Sr. Member
  • ****
  • Posts: 268
    • http://
Re: Guy wants me to pop a couple nuisance beavers
« Reply #16 on: May 11, 2010, 01:42:48 PM »
take a P1 and a Buck knife and go after him after you sting him with the P1 he will charge ya then jump on its back with the knife and finish him off
lol

Offline shady816

  • Sr. Member
  • ****
  • Posts: 327
    • http://thehowellnet.com:82
Re: Guy wants me to pop a couple nuisance beavers
« Reply #17 on: May 12, 2010, 02:51:00 AM »
I found that hanging a tree stand in a waterside tree gave the best result and the very top of a beaver skull is the best with lower powered guns hence the tree stand method and beavers can not look straight up while in water as well a elevated stand will be less likely a ricochet. I was taken on a few damage control hunts with a friend of my father when I was younger and this method for beavers was always the most successful.

Offline atchman2

  • Hero Member
  • *****
  • Posts: 1199
    • http://dxsinc.com
Re: Guy wants me to pop a couple nuisance beavers
« Reply #18 on: May 12, 2010, 05:00:52 PM »
I think I'd still use a powder burner on something that big.  However, I do like the tree stand idea and shooting straight down.  I'm pretty sure you could take him with a dead on shot from above.  Like you said his head isn't armored.
\"These birds are crapping on you even when their dead those are some bad dudes....\" Wingman115

Offline sumatrashooter

  • GTA Donations
  • ******
  • Posts: 5
Re: Guy wants me to pop a couple nuisance beavers
« Reply #19 on: May 29, 2010, 03:33:44 PM »
A powder burner isn't needed for sure.

I have a .25 caliber PCP magnum airgun. At 10 feet from the muzzle, it sends a 43 grain pellet at 950fps. That's 80fpe. At 50 yards, that's cut in half to about 40. Still 3 times more than is needed to kill the beaver. I've shot a .25 cal hole just about (the wood splinters blew out the back and the pellet deformed into the size of a quarter) through a 2x6 at 20 yards with it. It is nothing to shake a stick at.

There is a larger cousin to my gun that shoots 9MM pellets at 700+ fps and one that shoots .45 cal blackpowder bullets at 550fps. That's almost 200fpe. If you don't think an airgun can take a beaver, you need to take another look at the latest airguns!

If you take a look at Dennis Quackenbush's website, http://www.quackenbushairguns.com/ , he makes .458 caliber airguns that have taken down bison.

Long gone are the days were airguns are childs toys. They are viable hunting tools for animals up to 2000lbs.