Author Topic: Need a couple screws  (Read 1456 times)

Offline super fly

  • GTA Donations
  • ******
  • Posts: 3
Need a couple screws
« on: January 08, 2009, 03:22:26 PM »
I have a G1 xtreme and I need the two screws that hold the forearm of the stock to the receiver. I called crosman and they want 1$ per screw (which I didn't mind all that much) but then they wanted 4$ to ship them. Does any one have a couple of these screws or know where I can get them. I went to the local hardware store and got a couple that may work but the head on it is too big and is also slightly longer and not black so I'd rather not use them. Thanks in advance.

Offline bcshooter

  • Hero Member
  • *****
  • Posts: 616
    • http://
RE: Need a couple screws
« Reply #1 on: January 08, 2009, 03:30:56 PM »
Try Lowes or Home Depot in their speciality hardware section, Its the area that has pullout draws. Good Luck .......
AIR ARMS TX200 MkIII .22cal w/Bushnell Banner 6-18x50 AO      
BAM B 26   .177cal w/Centerpoint 4-16x40 AO/IR
BAM B 30-1 .177cal w/Leapers 4-16x50 AO/IR
CROSMAN 1377 .22cal w/UTG BugBuster 6x32 AO/IR
CROSMAN 2240 .177cal 10.1\" LW barrel w/UTG BugBuster 6x32 AO/IR
CROSMAN 2250B .22cal w/UTG Leapers 2-7x32 AO/IR
DIANA/RWS Model 34N .177cal w/Bushnell Sportsman 4-12x40 AO
DIANA/RWS Model 34P .22cal w/Centerpoint 4-16x40 AO/IR
DIANA/RWS Model 350 .22cal Feuerkraft Pro Compact w/Vortek PG-2 and Bushnell Banner 6-18x50 AO
DIANA/RWS Model 48  .177cal w/Centerpoint 4-16x40 AO/IR
DIANA/RWS Model 52   .22cal w/Leapers 4-16x50 AO/IR
DIANA/RWS Model 54  .177cal w/Leapers 4-16x50 AO/IR
DIANA/RWS Model 54   .22cal w/Leapers 4-16x50 AO/IR


Offline tjk

  • Hero Member
  • *****
  • Posts: 2275
    • http://
Re: Need a couple screws
« Reply #2 on: January 08, 2009, 04:18:49 PM »
Try using allen head bolts too. Better torqueing, and they are a lot less apt to marring. I would almost be positive that they are metric. Take along the old ones if you still have them and match them (threads and length) with a bolt you can find. If they are a too long, get two matching nuts,...one to gauge the depth and one to lock it in place. Them take a hack saw and cut off the un-needed portion. removing the nuts will clean off and de-burr the end of them. If needed, sand with a piece of emory cloth/strip for any remainning burrs you may encounter. I did this with most of my rifles, and they work,...and look alot better too! tjk
397 Benji-98\' model    
Marksman  0035, My Fav!,CDT T\'d
Crosman Sierra-Pro,.177
Benji 392 08\'
CDT TT\'d RWS 34 .22,CP 4-16X40 AO
MM T\'d Marksman 0035
Crosman G1 Extreme
Daisy PowerLine 1000
TF-97 .22
B-28A MM T\'d
B-28 OEM Tuned by me
Beeman .22 RX-2 w/Theoben GR
Beeman .177 R1 Santa Rosa

Offline Bentong

  • Hero Member
  • *****
  • Posts: 837
    • http://
RE: Need a couple screws
« Reply #3 on: January 10, 2009, 04:14:47 AM »
Quote
super fly - 1/8/2009  8:22 PM

I have a G1 xtreme and I need the two screws that hold the forearm of the stock to the receiver. I called crosman and they want 1$ per screw (which I didn't mind all that much) but then they wanted 4$ to ship them. Does any one have a couple of these screws or know where I can get them. I went to the local hardware store and got a couple that may work but the head on it is too big and is also slightly longer and not black so I'd rather not use them. Thanks in advance.


Go to Ace hardware and it's 25 cents each ask for item# 43556-P. I even replace the bolt that holds the action in the trigger guard item #42857-P. This are same with what you have know except they are allen vice phillips that tends to get rounded if not careful or to be on the safe side bring your old one and you can size it there. I have the bolts installed, perfect fit same lenght and head. It you want to they also have a nylon washer that will fit your breech washer after slight trimming by using a drill and spin it lightly on a 200 sandpaper. The installed ones in there are plastic and they tend to get squeezed. This made my G1 really extreme now. I can shoot a .177 pellet from 12 yards in door.   :p