« previous next »
Pages: [1]   Go Down

Author Topic: CFX help wanted  (Read 1708 times)

Offline mikeiniowa

  • Hero Member
  • *****
  • Posts: 1110
    • http://airgunartisans.com/flyingdragon
CFX help wanted
« on: September 30, 2007, 03:34:00 AM »
Have a CFX in the shop, never seen one before and want to get inside and do some tuning, how do you get to the front stock screws? Just pry the rubber inserts up and out? Thanks guys, Mike
Logged

Offline CharlieDaTuna

  • Hero Member
  • *****
  • Posts: 3405
    • http://www.charliedatuna.com
RE: CFX help wanted
« Reply #1 on: September 30, 2007, 03:43:01 AM »
That's it  Mike. Lift from under the rear at the center with a small screw driver, then grasp and pop out.
Logged
Bob  aka:  CharlieDaTuna
Co-founder of the GTA


HOME OF THE GRT-III TRIGGER
   Website:  http://charliedatuna.com/

Home of the NPSS-NP Triggers:  
            http://charliedatuna.com/NPSS.htm

E-Mail:  CDT22@Verizon.net

Benji-342 .177 /Brazilian Winchester 800 .22 /Gamo Cadet .177 /Gamo Shadowmatic .177 /Gamo 440 .22 /Gamo Royal .22 /Gamo Whisper .177 /Gamo SK-1 .20 /B-20 .177 /TF-99 .177 /QB-78 .177 /QB-78t .22 /QB-78-(CD) .22 /QB-78-(CJ) .22/QB-78D .22 /Crosman 2240 .22 /Cros 150 .177 /Crosman Back Packer .22 ?Crosman AS 2250 .22 /Daisy Mod 93 .177 /Marksman 2004 .177 /GS 35 .177 /FWB-124 .177 /Custom Marauder .22 /Custom Disco .177

Offline PeakChick

  • Hero Member
  • *****
  • Posts: 2029
    • http://
RE: CFX help wanted
« Reply #2 on: September 30, 2007, 03:57:00 AM »
Yep, exactly what Bob said. I may add a couple of observations from my CFXs. Go slow with prying the covers off, it is possible to tear off the rubber studs on them. Also, the stock screws are Torx head screws.
Logged
The current stable, (arsenal, quiver?): BSA Lightning XL .177, BSA Sportsman HV .22, BSA Ultra .177, CZ634 .177, Daystate Harrier X .177, TAU 200 Senior .177, HW 97 .177, HW 50s .177, HW 30 .177, RWS 92 .177, Gamo 126 MC Super, Gamo Big Cat .177, AR2078A, QB78 .177, Quest 1000 .177, Beeman SS650 .177., Beeman P17 .177.
________________________________________

Those who do not learn the lessons of history are doomed to repeat it.

Offline mikeiniowa

  • Hero Member
  • *****
  • Posts: 1110
    • http://airgunartisans.com/flyingdragon
RE: CFX help wanted
« Reply #3 on: September 30, 2007, 03:13:50 PM »
I noticed the Torx screws, now have to buy a set to do the work. Haven't had a CFX in the shop before, nice to start with, just wonder how good it will be when I get done.............thanks fore the help both of you, Mike
Logged

Offline CFX Marauder

  • Hero Member
  • *****
  • Posts: 953
    • http://s241.photobucket.com/albums/ff275/Cfx-131/
Re: CFX help wanted
« Reply #4 on: October 01, 2007, 01:03:04 PM »
Lil OT but has anyone tried dying the inserts? I was wondering if one of the automotive interior dyes would hold and last...
Logged
JOIN THE NRA !! FREE Enrollment !! https://www.nrahq.org/nrabonus/accept-membership.asp
2009 Total
34 Tree Rats
10 Grackles
6 Starlings
Quote
shadow - 9/25/2008 8:00 PM  Pigeons in a dark barns, they seemed to get very alarmed by that red beam following them around. Ed
Quote
ronbeaux - 5/6/2009  10:36 PM \" Give em the lead boys and make a big hole, wanna watch em dance and steal the show\"

Offline SDale

  • Hero Member
  • *****
  • Posts: 1868
    • http://
Re: CFX help wanted
« Reply #5 on: October 01, 2007, 03:00:50 PM »
I haven't dyed the CFX inserts, but I've dyed many Hogue Overmolded stocks. The overmolding is probably the same rubber/plastic. Automotive dyes will work just fine. Just make sure to degrease the pads really well first with denatured alcahol.
Logged
Pages: [1]   Go Up
« previous next »