« previous next »
Pages: [1]   Go Down

Author Topic: OK, where do I get those mods for my new Disco  (Read 3364 times)

Offline Gene_SC

  • Hero Member
  • *****
  • Posts: 11378
    • http://www.airguntoys.com
OK, where do I get those mods for my new Disco
« on: October 20, 2009, 12:15:33 AM »
Looking for new higher breech block which would be made of steel. New barrel band to match. And any other good aftermarketgizmos thatwill increase performance..:)
Logged
THE ONES I SLEEP WITH: BSA Lightning XL, AA TX-200, AA ProSport, BSA Ultra, HW-97K, Crosman NPSS .177, FX Cyclone, HW-30 Nicle Plated, AA-S200, Crosman Marauder, CZ-634, R-9 DG, Webley/Scott UK Tomahawk, Benji Kantana, Benji Marauder, Benji Discovery.....
....

Gene\'s Tunz n Toyz
Springer Tunin

Offline spysir

  • Full Member
  • ***
  • Posts: 210
    • http://
RE: OK, where do I get those mods for my new Disco
« Reply #1 on: October 20, 2009, 04:26:37 AM »
I personally do not have one ( I do have a .177 Disco) but I am think an RJ high rise breech should fit.  Need power ? I recently tried one of those $8.00 22xx POWER springs in ours, with a touch of an overfill (2200psi) it shot JSB at 24.8fpe , that is in .177. I believe the fellow selling them can be reached at    hyperbotfly@yahoo.com  

 John
Logged

Offline Bhawanna

  • Hero Member
  • *****
  • Posts: 1065
    • http://airgunrecon.com
RE: OK, where do I get those mods for my new Disco
« Reply #2 on: October 20, 2009, 12:48:34 PM »
google rjmachine.  he makes the risers.  about $100.
Logged
The hardest part of getting old is trying to look good naked!

Offline Gene_SC

  • Hero Member
  • *****
  • Posts: 11378
    • http://www.airguntoys.com
Re: OK, where do I get those mods for my new Disco
« Reply #3 on: October 20, 2009, 01:14:55 PM »
Ok so if I get the high riser then I will need to change the barrel band. Does he sell them also.. I looked on his site and he does not mention the Disco but only the QB's and Crosman pistola's.
Logged
THE ONES I SLEEP WITH: BSA Lightning XL, AA TX-200, AA ProSport, BSA Ultra, HW-97K, Crosman NPSS .177, FX Cyclone, HW-30 Nicle Plated, AA-S200, Crosman Marauder, CZ-634, R-9 DG, Webley/Scott UK Tomahawk, Benji Kantana, Benji Marauder, Benji Discovery.....
....

Gene\'s Tunz n Toyz
Springer Tunin

Offline Bhawanna

  • Hero Member
  • *****
  • Posts: 1065
    • http://airgunrecon.com
its my understanding.....
« Reply #4 on: October 20, 2009, 01:44:02 PM »
the 2240 breech is the same as the discovery....i may be wrong but i think this is correct.
Logged
The hardest part of getting old is trying to look good naked!

Offline Timmyj1959@yahoo.com

  • Hero Member
  • *****
  • Posts: 3716
    • http://dragonslayer
RE: OK, where do I get those mods for my new Disco
« Reply #5 on: October 20, 2009, 02:58:09 PM »
The 22 XX breach,s either steel or plastic are differant than the Discovery. The allen screw is in a differant location on the Disco involving removing the bolt for acsess. Also the front of the Disco breach block is bored out to accept the "sight extension". Other than cosmetics the 22XX & disco brl bands are interchangable. Grade #3: XX brl band,, painted with obvious mold lines. Grade #2:Crosman custom shop brl. band with a slight attempt to remove mold lines slightly better in appearance. Grade #1: Discovery brl. band,, machined very smooth & nice. All interchangeable though. Triple A Grade: One made by Gene or "Mr Bob"!! Tim.
Logged

Offline spysir

  • Full Member
  • ***
  • Posts: 210
    • http://
RJ breech
« Reply #6 on: October 26, 2009, 05:38:23 PM »
will fit a Disco, the newer 22xx have a differnt screw location than the older ones. Also the RJ breech is much beefier providing better support for the barrel, no band is required (maybe nice but not needed) when using his breech with a 20" barrel on a 22xx.
John
Logged

Offline Crimson Sky

  • Full Member
  • ***
  • Posts: 140
    • http://www.thebestcasescenario.com
Re: OK, where do I get those mods for my new Disco
« Reply #7 on: November 07, 2009, 01:20:22 AM »


Gene, Don Cothran made some amazingly beautiful Crosman 22xx parts for me to have on the American Airgunner show. Stainless steel, NASA grade perfection, or aluminum if you prefer. Here is his website:



http://cothranmachine.com/ItemDisplay.php

Logged
Pages: [1]   Go Up
« previous next »