BEST AIR GUN HAS THE FAST DEER AT ABOUT $20.00

[howie1a]

This is about as low as I've seen for the Fast Deer, not a bad deal.

[vinceb]

...or warranty. Wonder how they wound up with a bunch like that?

AND FOR THE NEWBIES - do NOT believe the published velocity figures. You can count on about 600fps in .177 and 450-500 in .22 caliber.

[PALTIK]

Only selling the 0.177's. I could've been tempted but there was no 0.22.
Nice find though.
Thanks still.  =)

[howie1a]

I couldn't fine a Fast Deer in 22 cal and I looked every where. The deer as well as all china rifles FPS are not true But they still are nice rifles I don't know what they used for pellets Maybe Gamos gold raptors.. But the FPS are bull. howie

[tedshred]

Shipping to my area was only 12.00 for two of them.  Will likely be doing some experimental modifications with them to see how things go.

[derekmcminn]

Just added it to my collection and ordered one tonight. Total is $31.90, not bad for a .177 project springer. Thanks for the heads up.

[Machinist]

Ted:
Where is your area? Could you tell us where Best Airgun is located. They don't answer e-mail.
Like you, I could use a couple parts guns.
Mike

[howie1a]

I ordered one too   I loved the deer I had before. howie

[Curioguy]

Thanks Howie, just another temptation for me to fight. Just think, cheaper than a Tools Now B3 and you don’t have to remove that ugly front sight (on the B3).

[howie1a]

Random quote: Dont do drugs, You cant be a Pro Airgun hunter like me if your off doing drugs...
- (Added by: yotehunter)


How to make a mussel break out of gal. pipe.pictures
Moderators: fix, DanoInTx, Splash

   View previous thread :: View next thread
Reply New post    General Discussion To Gateway To Airguns -> The Shop   Message format
 
howie1a
   
Posted 4/5/2008 3:20 PM (#54086)
Subject: How to make a mussel break out of gal. pipe.pictures   Quote Reply Alert
Online

Extreme Veteran

Posts: 338
100
Location: st pete fl   I was making 2 new mussel breaks and thought maybe one of the members might like to see the steps I took in making them , from 2 galvinized pipe nipples 1/2 inch x 5 inches and 2 washers , after they are finished all that is needed to do is ream them out to a sliding fit over the barrel and drill and tap 2 screw holes in the break for clamping them to the barrel .Howie

I tried to move the pictures from the old post but they wouldn't work but you can pull up the pictures up from the(( search ))the location is the shop and 4-5-2008 take a look howie

[tedshred]

I'm in Eugene, Oregon.

From their site:

Best Airgun
http://www.BestAirgun.com

Bestcom Group, Inc.
24910 Cactus Sage Trl
Katy, TX 77494
BestAirgun@Yahoo.com

[howie1a]

You use a 1/2 inch pipe nipple and solder a washer on the end to get started then grind down the threaded end the npt starts the taper for you and drill and tap 2   4-40 holes to put the allen set screws in and fine sand and blue. about an hours work no big deal. howie

[howie1a]

If other members are buying the best airgun without the front sight how come their are so many Fast deers without front sights or did best airgun take them off to promote sales and what are they going to do with all those sights? May be sell them to all us guys that have fast deers with out front sights ???

[derekmcminn]

howie1a - 6/24/2008  7:20 AM

If other members are buying the best airgun without the front sight how come their are so many Fast deers without front sights or did best airgun take them off to promote sales and what are they going to do with all those sights? May be sell them to all us guys that have fast deers with out front sights ???

They were all probably shipped from the factory without front sights. They were probably coming already bent out of shape, the American distributors complained, so the Chinese yanked them all out. The question is, what are the Chinese going to do with all those front sights?

[tedshred]

China:
Foreman: "Did you box up that large shipment of KL3B's for BestAirGun?"
Employee: "No, glorious foreman, we are still waiting on the front sights which are delayed due to earthquakes"
Foreman: "Go ahead and box them up anyway. They are creating a log-jam in the factory"
Employee: "Wont the Americans be upset the rifle is missing a part?"
Foreman: "Maybe, but they will always buy more. That's what they do, consume! LOL"
Employee: "hahaha"

BestAirGun:
Receiving dept: "All these KL3B's are defective as they are missing the front sights!"
Sales Manager: "That's okay, just mark them down to $20.00 and move them out. This rifle is usually a project gun anyway, so we'll say something like that in the copy. Heck, they may just start buying more of our scopes because of it, which we have a larger profit margin anyway. Hahaha"
Receiving dept: "hahahahaha"

American airgun consumer: "Sweet! BestAirGun is unloading the Fast Deer for cheap because it's missing a front scope. Might as well buy two of them and make a project out of them. Hahaha"